3 SITES IN PRODUCTION · FRANCE + SLOVAKIA
Stack of laser-cut steel parts
05 / Cutting

Cutting post-processing

Cut parts are deburred, flattened, bevelled and shot blasted before they leave us. Your welding shop or assembly line receives parts ready to use, with no rework step at your site.

100%
Material shot blasted before or after cutting
100%
Parts deburred after cutting
350 t
Flattening press force
01 / Cutting

Flattening

Removing distortion after cutting

Flattening removes cutting distortion before the parts reach bending or welding.

Press flattening a thick cut steel part
  • Feature

    350 t Colly flattening press, parts up to 6000 × 3000 mm

    Benefit

    Large and thick cut parts are flat when they reach your jig, so they fit without forcing.

    Proof

    350 t · 6000 × 3000 mm

  • Feature

    Automatic 19-roll leveller, 1250 mm passage, up to 20 mm thick

    Benefit

    Series of smaller parts are levelled in one automatic pass.

    Proof

    19 rolls · 1250 mm

02 / Cutting

Deburring

Removing sharp edges after cutting

Deburring removes the sharp cutting edge before the parts are handled and assembled.

Operator feeding cut steel parts into the automatic deburring machine
  • Feature

    Automatic double-sided Arku deburring machine

    Benefit

    Both faces are deburred in one pass: no manual grinding before welding or painting.

    Proof

    Arku · 2 sides

  • Feature

    Parts up to 1250 mm wide and 20 mm thick

    Benefit

    Your operators handle the parts without sharp edges, and the finish is the same on every part.

    Proof

    1250 mm · 20 mm

  • Feature

    Every cut part is deburred

    Benefit

    No sorting or burr check needed at your goods-in.

    Proof

    100%

03 / Cutting

Chamfering & weld bevelling

Making your welding easier

Bevelling prepares plate edges for your welds.

Plasma torch bevelling the edge of a steel plate
  • Feature

    Cortina chamfering machine, bevel angles from 10° to 50°

    Benefit

    Weld preparations are machined to the angle on your drawing: better penetration and no edge grinding in your welding shop.

    Proof

    10°–50°

  • Feature

    1500 × 3000 mm table

    Benefit

    Plate parts up to this format are bevelled right after cutting, before they leave us.

    Proof

    1500 × 3000 mm

04 / Cutting

Shot blasting

Preparing material for welding and painting

Shot blasting prepares the steel surface for welding and painting.

Cut steel parts on the roller conveyor of the shot blasting line
  • Feature

    All the material we cut is shot blasted, before or after cutting

    Benefit

    Parts arrive free of mill scale, ready for welding and paint, with no blasting step at your site.

    Proof

    100%

  • Feature

    Tosca blasting machine, up to 2500 mm wide and 300 mm thick

    Benefit

    Wide plates and large cut parts go through the same blasting line as small ones.

    Proof

    2500 mm

FAQ

Frequently asked questions

Are cut parts delivered deburred?

Yes, 100% of parts are deburred after cutting, on an automatic double-sided Arku machine that takes parts up to 1250 mm wide and 20 mm thick. You receive them ready to handle and assemble.

Can you flatten parts after cutting?

Yes. We have a 350 t Colly flattening press for parts up to 6000 × 3000 mm, and an automatic 19-roll leveller with a 1250 mm passage width for thicknesses up to 20 mm. Parts reach your jig flat.

Can you bevel plate edges for welding?

Yes. Our Cortina chamfering machine has a 1500 × 3000 mm table and bevels edges at angles from 10° to 50°, which improves weld penetration.

Is the material shot blasted?

Yes, all the material we cut is shot blasted, before or after cutting, on a Tosca machine that takes material up to 2500 mm wide and 300 mm thick. Parts arrive ready for welding and painting.

Have a drawing? We'll tell you exactly how we'd make it.